FTDX1200 Operating Manual Page 113

MENU MODE Cont'd
Previous Page    Index of Topics    Table of Contents    Index of Pages    Next Page
MENU ITEM DETAILS Cont'd
015 ROTATOR OFFSET ADJ
Function: Adjusts the indicator needle precisely to the starting point set in Menu item "014 ROTATOR STARTUP".
Available Values: -30 degrees ~ 0 degrees (2 degree step)
Default Setting: 0 degrees

ADVICE: If the optional Antenna Rotator is not connected, this adjustment has no effect.

End of "Display Group

DVS GROUP
016 RX OUT LEVEL
Function: Sets the audio output level from the optional DVS-6 Voice Memory Unit.
Available Values: 0 ~ 100
Default Setting: 50

ADVICE: If the optional DVS-6 Voice Memory Unit is not connected, this adjustment has no effect.

017 TX OUT LEVEL
Function: Sets the microphone input level to the optional DVS-6 Voice Memory Unit.
Available Values: 0 ~ 100
Default Setting: 50

ADVICE: If the optional DVS-6 Voice Memory Unit is not connected, this adjustment has no effect.

End of "DVS Group"

KEYER GROUP

018 F KEYER TYPE
Function: Selects the desired keyer operation mode to the device connected to the front panel KEY jack.
Available Values: OFF, BUG, ELEKEY or ACS
Default Setting: ELEKEY

OFF: Disables the front panel keyer ("straight key" mode for use with external keyer or computer-driven keyer interface).

BUG: Mechanical "bug" keyer emulation. One paddle produces "dits" automatically, while the other paddle manually produces "dahs".

ELEKEY: Iambic keyer with ACS (Automatic Character Spacing) disabled.

ACS: Iambic keyer with ACS (Automatic Character Spacing) enabled.

019 F CW KEYER
Function: Selects the keyer paddle wiring configuration for the KEY jack on the front panel.
Available Values: NOR or REV
Default Setting: NOR

NOR: Tip=Dot, Ring=Dash, Shaft=Ground.

REV: Tip=Dash, Ring=Dit, Shaft=Ground.

020 R KEYER TYPE
Function: Selects the desired keyer operation mode to the device connected to the rear panel KEY jack.
Available Values: OFF, BUG, ELEKEY or ACS
Default Setting: ELEKEY

OFF: Disables the rear panel keyer ("straight key" mode for use with external keyer or computer-driven keyer interface).

BUG: Mechanical "bug" keyer emulation. One paddle produces "dits" automatically, while the other paddle manually produces "dahs".

ELEKEY: Iambic keyer with ACS (Automatic Character Spacing) disabled.

ACS: Iambic keyer with ACS (Automatic Character Spacing) enabled.

021 R CW KEYER
Function: Selects the keyer paddle wiring configuration for the KEY jack on the rear panel.
Available Values: NOR or REV
Default Setting: NOR

NOR: Tip=Dot, Ring=Dash, Shaft=Ground.

REV: Tip=Dash, Ring=Dit, Shaft=Ground.

022 ELEKEY TYPE
Function: Selects the operation mode of the internal keyer.
Available Values: ELEKAY-A or ELEKEY-B
Default Setting: ELEKEY-B

023 CW WEIGHT
Function: Sets the Dot:Dash radio for the buit-in electronic keyer.
Available Values: (1:) 2.5 ~ 4.5
Default Setting: 3.0

024 BEACON TIME
Function: Sets the interval time between repeats of the beacon message.
Available Values: OFF, 1 ~ 240 sec (1 sec/step) or 270 ~ 690 sec (30 sec/step)
Default Setting: OFF

Cont'd Next Page Menu Item Details
"Keyer Group"

Cont'd Next Page "Menu Item Details"
Previous Page    Index of Topics    Table of Contents    Back to Top    Index of Pages    Next Page
FTDX1200 Operating Manual Page 113